CircuitValley : Embedded Engineering

This post this Part 5 in the Multi part Series of the , Part 1 we Compared sensor, Part 2 was Hardware and Mechanical Design, Part 3 about Sensor Solution, Part 4 About Software Arch, This Part 5 is going in details about FPGA/PL Pipeline.

This post this Part 4 in the Multi part Series of the , Part1 we Compared sensor, Part2 was Hardware and Mechanical Design, Part3 about Sensor Solution.

This is Part 3 the CHC5 Camera System Posts, in Last post I showed how CHC5 Camera architecture is designed and everything is put together at system design and ISP level.

This project is the next project in the series of camera projects that have been published on CircuitValley.

There many Sensors Available on this Whole CHC5 Camera Platform These Sensor PCB are Part of this Modularity Them so these Sensor PCB can be used with CHC5 and also Other System CircuitValley Make Specially MIPI FMC Board.

This post is going to about a really special FMC LPC board for Xilinx FPGA boards.

As I am working with more High end FPGA boards.

Prototyping with advanced FPGA boards is quite challenging, As they often have very high density connectors for expansions and peripherals.

This project is going to show you a very very small RF Signal Generator 35Mhz to 4.4Ghz on a Tiny PCB that can be easily integrated into project. this Project is complement to USB RF signal generator which I published few weeks ago.

This post is going to be about how to Create FSBL for Zynq SOC, Using newer version of Vitis 2024.2 .

This project is in continuation of the project that I have previously published making Sin Wave Galvanically Isolated Distribution Amplifier for GPSDO and Lab Reference.

KLIP30 USB Programmable 30ps Fast Pulse Generator Programmable DC Coupled Output with 50mV to 1300mV Signal Amplitude with 50Ω Output Very Fast ~20ps Falling Time and 30ps Rise time with Uncertainties + 1.6ps to – 1.8ps Programmable output frequency PLL S…

This Project is going to be about making a fully open source USB Programmable RF signal Generator.

This Post is going to be Ikea INSPELNING Tear down images.

This post is going to be about Breakout board PCB for FMC Connector which are widely used on Xilinx High End FPGA board.

Ribbon cable are used to Distribute power to all other boards Input Primary power of 16 to 20 V and USB 5V both are distributed over Ribbon cable 3D Printed Part Plastic Part is Designed with Solidworks and Printed with PETG.

This is Next 3V1 revision of LM399 ADR1399KHZ based reference board, when i made my last version i received quite few small feedback form users , So I have again made few improvements in This forth version over Third reversion accumulating those suggestio…

For new FPGA SoC related project, and i will be using Avnet MicroZed Zynq SOM board.

This small Article shows my solution to Low noise electronics bench lighting problem, Many electronics Measurement needs to be done in no electrical noise environment.

This Small Article shows internals of BADRING Water leakage sensor Video

This Small Article shows internals of PARASOLL Smart Door/Window Zigbee Sensor and analysis of its hall effect sensor using a oscilloscope Front PCB EFR32MG24 along with a LED , Oscillator and Passives for antenna.

This Small Article shows internals of Ikea Vallhorn PIR Motion Sensor Board uses EFR32MG21 Silicon labs Multiprotocol SOC along with 8601 Opamp IC from analog devices.

This Post is showing how to Reverse Engineer a Unknown FPGA Board which I got off Ebay.

This is Third version of LM399 ADR1399KHZ based reference board, when i made my last version i received quite few small feedback form users , So I have again made few improvements in Third reversion accumulating those suggestions.

This Post is going to be Ikea TRETAKT Tear down images.